1.准确行星减速、功效提高、运行平稳；

　　1. Accurate planetary deceleration, improved efficiency, and smooth operation;

　　2.绝缘工程材料机壳、双重绝缘、坚固可靠；

　　2. High quality insulation engineering material casing, double insulation, safe, sturdy and reliable;

　　3.高速马达、低噪音、大功率、额定电压220V50/60Hz；

　　3. High speed motor, low noise, high power, rated voltage 220V50/60Hz;

　　4.枪式握把、负荷人体工学、增加握持力、减轻疲劳强度；

　　4. Gun style grip, ergonomic load-bearing design, increased grip strength, and reduced fatigue intensity;

　　一，使用方法：

　　1、 Usage:

　　1、 用扳手内套筒完全插进螺栓尾部梅花头部分，同时向前推动扳手，内套筒后退，使外套筒完全套住螺母，若不能完全套住螺母请左右转动扳手并向前用力。

　　1. Insert the inner socket of the wrench completely into the plum blossom head at the end of the bolt, and push the wrench forward at the same time. Move the inner socket back to fully cover the nut with the outer sleeve. If the nut cannot be fully covered, turn the wrench left and right and apply force forward.

　　2、 扣动扳手开关，使其旋转。

　　2. Turn the wrench switch to rotate it.

　　3、 拧断梅花头，紧固结束，同时扣动板机弹出梅花头。

　　3. Twist off the plum blossom head, tighten it, and at the same time, press the trigger to pop out the plum blossom head.

　　二，套筒更换：

　　2、 Sleeve replacement:

　　1、 把扳手外部的两个定位螺钉松开，把外套筒、内套筒及内套筒弹簧取出。

　　1. Loosen the two positioning screws on the outside of the wrench, and remove the outer sleeve, inner sleeve, and inner sleeve spring.

　　2、 先装上内套筒的弹簧及所换内套筒，然后装上相应的外套筒，前壳体凸起部与外套筒凹下部相连接，并把两个定位螺钉拧紧。

　　2. First, install the spring of the inner sleeve and the replaced inner sleeve, then install the corresponding outer sleeve. Connect the protruding part of the front shell to the concave part of the outer sleeve, and tighten the two positioning screws.

　　三，检查与维修

　　3、 Inspection and Maintenance

　　1、 定期检查电源线，如果有破裂或断线应及时更换。

　　1. Regularly check the power cord, and replace it promptly if it is broken or disconnected.

　　2、 使用前应检查各紧固螺钉是否松动，如果松动应及时紧固，并试转声音是否正常，如果出现异常声音应及时检修。

　　2. Before use, check whether each fastening screw is loose. If it is loose, tighten it in a timely manner and test whether the sound is normal. If there is any abnormal sound, repair it in a timely manner.

　　保持内外套筒清洁不得混入杂物。

　　Keep the inner and outer sleeves clean and free from impurities.

　　用完本机后应擦拭干净存放于干燥处

　　After using this machine, it should be wiped clean and stored in a dry place

　　四，注意事项：

　　4、 Attention:

　　1、 本机所用电源应在本机规定的范围内，否则会造成机器故障。

　　1. The power supply used for this machine should be within the specified range, otherwise it may cause machine malfunction.

　　2、 不可在雨天或潮湿的环境中使用本机，以免漏电。

　　2. Do not use this machine in rainy or humid environments to avoid electrical leakage.

　　3、 使用本机高空作业时，请系好带，在操作点下方严禁站人及放置贵重物品。

　　3. When using this machine for high-altitude operations, please fasten your seat belt. It is strictly prohibited to stand or place valuable items below the operating point.

　　4、 使用本机时需远离易燃易爆物品。

　　4. Keep away from flammable and explosive materials when using this machine.

　　5、 严禁破坏电源线及使用电源线拖拉本机。

　　5. It is strictly prohibited to damage the power cord and drag the machine with the power cord.

　　6、 检查及维修本机时应先切断电源。

　　6. When inspecting and repairing this machine, the power should be cut off first.

　　7、 严禁过重碰撞本机。

　　7. Heavy collisions with this machine are strictly prohibited.

　　8、 当机器发烫或环境温度大于35℃时，应停止使用。

　　8. When the machine heats up or the ambient temperature exceeds 35 ℃, it should be stopped from use.

　　9、 定期检查碳刷，当碳刷长度小于原长度2/5时，应及时更换。

　　9. Regularly check the carbon brush, and replace it in a timely manner when the length of the carbon brush is less than 2/5 of the original length.

本文扭剪螺栓专用扳手友情奉献.更多有关的知识请点击https://www.xjnwz.com/:真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article presents a dedicated wrench for twisting and cutting bolts. For more related knowledge, please click here https://www.xjnwz.com/: Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned