租用扭剪扳手 对外出租扭剪型电动扳手 扭剪扳手租赁
Rent the torsion shear wrench, rent the torsion shear type electric wrench, and rent the torsion shear wrench
本公司对外出租扭剪型电动扳手，x24j扭剪扳手适用于M16.20.22.24四种扭剪螺栓，x30j-2扭剪扳手适用于M16.20.22.24.27.30六种扭剪螺栓
The company rents out torsion shear electric wrenches. X24j torsion shear wrenches are applicable to m16.20.22.24 four kinds of torsion shear bolts, and x30j-2 torsion shear wrenches are applicable to m16.20.22.24.27.30 six kinds of torsion shear bolts
对外出租的扭剪扳手，租用的是平时厂里的备用扳手，有意者可以联系公司销售部。
For the externally rented torsion shear wrenches, the spare wrenches in the factory are rented. Interested parties can contact the Sales Department of the company.
1，计算需要的扭矩值，这里以高强度螺栓为例：
1. First, calculate the required torque value. Here, take the high-strength bolt as an example:
终拧扭矩值=扭矩系数*预拉力值标准值*螺栓公称直径
Final tightening torque value = torque coefficient * pretension value (standard value) * nominal diameter of bolt
2，设定好一个需要的扭矩值。
2. Set a required torque value.
调节完后中间竖杆可塞回。
The middle vertical rod can be plugged back after adjustment.
3，设定扭矩后，将套筒插入方形驱动头。
3. After setting the torque, insert the sleeve into the square drive head.
4，通过调整卡子的位置来调节顺/逆时针旋转方向。
4. Adjust the clockwise / counterclockwise rotation direction by adjusting the position of the clip.
5，将套筒套在螺栓头部或螺母上，本示例是套在螺帽上。
5. Put the sleeve on the bolt head or nut, and this example is on the nut.
6，在扭紧的有时候螺帽和螺母会同时转动，需要用一个扳手卡紧螺母，之后顺时针转动扭矩扳手再对螺帽进行紧固。
6. When tightening, sometimes the nut and nut will rotate at the same time. It is necessary to clamp the nut with a wrench, and then turn the torque wrench clockwise to tighten the nut.
（PS:扭矩很大时，可外加接长套杆以便操作省力。）
(PS: when the torque is large, an extension sleeve rod can be added to save labor.)
7，在施力过程中，按照标准仪器操作规范，其垂直度偏差左右不应超过10度。其水平方向上下偏差不应超过3度，操作人员在使用过程中应保证其上下左右施力范围均不超过15度。
7. In the process of applying force, according to the national standard instrument operation specification, the verticality deviation shall not exceed 10 degrees. The vertical deviation in the horizontal direction shall not exceed 3 degrees, and the operator shall ensure that the upper, lower, left and right force ranges do not exceed 15 degrees during use.
8，听到“咔嗒”声后，紧固结束，然后应及时解除作用力。
8. After the "click" sound is heard, the fastening is completed, and then the force shall be released in time.
9，扳手是测量工具，应轻拿轻放，不能代替榔头敲打，如长期不用，调节标尺刻线退扭矩小数值处，有利于保证扭矩的精度。存放于干燥处。
9. The wrench is a measuring tool and should be handled with care. It can not replace the hammer to knock. If it is not used for a long time, adjust the scale score to the small value of torque, which is conducive to ensuring the accuracy of torque. Store in a dry place.
The above is the detailed introduction of the torsion shear wrench. I hope it will help you. If you have any questions, please contact us. We will provide you with services in a professional manner https://www.xjnwz.com
